zinject

Section: System Administration Commands (8)
Updated: 2013 FEB 28
Index Return to Main Contents

 

NAME

zinject - ZFS Fault Injector  

DESCRIPTION

zinject creates artificial problems in a ZFS pool by simulating data corruption or device failures. This program is dangerous.  

SYNOPSIS

zinject
List injection records.
zinject -b objset:object:level:blkd [-f frequency] [-amu] pool
Force an error into the pool at a bookmark.
zinject -c <id | all>
Cancel injection records.
zinject -d vdev -A <degrade|fault> pool
Force a vdev into the DEGRADED or FAULTED state.
zinject -d vdev -D latency:lanes pool

Add an artificial delay to IO requests on a particular device, such that the requests take a minimum of 'latency' milliseconds to complete. Each delay has an associated number of 'lanes' which defines the number of concurrent IO requests that can be processed.

For example, with a single lane delay of 10 ms (-D 10:1), the device will only be able to service a single IO request at a time with each request taking 10 ms to complete. So, if only a single request is submitted every 10 ms, the average latency will be 10 ms; but if more than one request is submitted every 10 ms, the average latency will be more than 10 ms.

Similarly, if a delay of 10 ms is specified to have two lanes (-D 10:2), then the device will be able to service two requests at a time, each with a minimum latency of 10 ms. So, if two requests are submitted every 10 ms, then the average latency will be 10 ms; but if more than two requests are submitted every 10 ms, the average latency will be more than 10 ms.

Also note, these delays are additive. So two invocations of '-D 10:1', is roughly equivalent to a single invocation of '-D 10:2'. This also means, one can specify multiple lanes with differing target latencies. For example, an invocation of '-D 10:1' followed by '-D 25:2' will create 3 lanes on the device; one lane with a latency of 10 ms and two lanes with a 25 ms latency.

zinject -d vdev [-e device_error] [-L label_error] [-T failure] [-F] pool
Force a vdev error.
zinject -I [-s seconds | -g txgs] pool
Simulate a hardware failure that fails to honor a cache flush.
zinject -p function pool
Panic inside the specified function.
zinject -t data [-e device_error] [-f frequency] [-l level] [-r range] [-amq] path
Force an error into the contents of a file.
zinject -t dnode [-e device_error] [-f frequency] [-l level] [-amq] path
Force an error into the metadnode for a file or directory.
zinject -t mos_type [-e device_error] [-f frequency] [-l level] [-r range] [-amqu] pool
Force an error into the MOS of a pool.
 

OPTIONS

-a
Flush the ARC before injection.
-b objset:object:level:start:end
Force an error into the pool at this bookmark tuple. Each number is in hexidecimal, and only one block can be specified.
-d vdev
A vdev specified by path or GUID.
-e device_error
Specify checksum for an ECKSUM error, dtl for an ECHILD error, io for an EIO error where reopening the device will succeed, or nxio for an ENXIO error where reopening the device will fail.
-f frequency
Only inject errors a fraction of the time. Expressed as an integer percentage between 1 and 100.
-F
Fail faster. Do fewer checks.
-g txgs
Run for this many transaction groups before reporting failure.
-h
Print the usage message.
-l level
Inject an error at a particular block level. The default is 0.
-L label_error
Set the label error region to one of nvlist, pad1, pad2, or uber.
-m
Automatically remount the underlying filesystem.
-q
Quiet mode. Only print the handler number added.
-r range
Inject an error over a particular logical range of an object, which will be translated to the appropriate blkid range according to the object's properties.
-s seconds
Run for this many seconds before reporting failure.
-T failure
Set the failure type to one of all, claim, free, read, or write.
-t mos_type
Set this to mos for any data in the MOS, mosdir for an object directory, config for the pool configuration, bpobj for the block pointer list, spacemap for the space map, metaslab for the metaslab, or errlog for the persistent error log.
-u
Unload the pool after injection.

 

ENVIRONMENT VARIABLES

ZINJECT_DEBUG
Run zinject in debug mode.

 

AUTHORS

This man page was written by Darik Horn <dajhorn@vanadac.com> excerpting the zinject usage message and source code.

 

SEE ALSO

zpool(8), zfs(8)


 

Index

NAME
DESCRIPTION
SYNOPSIS
OPTIONS
ENVIRONMENT VARIABLES
AUTHORS
SEE ALSO

This document was created by man2html, using the manual pages.
Time: 15:40:08 GMT, December 01, 2016